Welcome to Robit Plc's second quarter and half-year results analyst and press conference. My name is Arto Halonen and I'm the CEO of Robit Plc. And I'm here with Ville Peltonen, our CFO. We'll start the event with a presentation. And after the presentation, we'll have a Q&A session.
You have the possibility to ask questions either through the chat channel, which is open and live already, so you can post questions at any time, or you can ask questions through the teleconference by using the raise hand functionality that you should see on your end. But let's get going. First, the standard disclaimer about the forward-looking statements. And the results. So, for quarter two 2024, we recorded healthy growth in orders received. As well as a clear improvement in our profitability.
If you look at market demand, the demand within the mining sector remained good and satisfactory in the construction sector. We didn't see the recovery in the construction demand that we had anticipated earlier this year. That recovery is expected to start gradually towards the end of the year, and we expect the construction market to remain at the current satisfactory level. Also until the end of 2024. Our orders received grew by 13.6%.
This growth was driven by our Top Hammer business, but also, despite the lower underlying demand in the construction segment, we recorded healthy growth in the geotechnical business. This growth was driven by a couple of large orders that we secured. Our net sales grew by 0.9% in constant currencies and resulted in €24.6 million. The growth came from the Top Hammer segment and especially from the Australasia market.
Our profitability also clearly improved a comparable EBIT of €0.7 million compared to €0.2 million in the comparison period. The improvement was driven by the savings actions that we have been implementing over the last 12 months, which are clearly visible in the results. However, the improvement was below our targets as we had high freight costs during the quarter; we were forced to use a high share of air freight during the quarter, which impacted our profitability negatively. We did this to maintain a good service level to our customers.
One highlight is our clearly improved financial position. So gearing now is 34.6% compared to 59.6% 12 months back. This is a result of the improved profitability as well as the positive cash flow generated during this period. The net cash flow from operating activities was €2 million in the quarter. We did see some increase in our inventories, the transit times have increased, causing inventory to be in transit for a longer time, therefore increasing our inventories. And also, we ramped up the inventory for some of the customers we secured during the quarter.
I'm also pleased to see that we have taken some clear steps towards our sustainability targets. Especially, I would say, as a highlight, is the CO2 emission intensity which is now 36% below the benchmark year, or the baseline year of 2020. This is a ten percentage point decrease from the end of last year. Clear, clear, step forward on this one as well. If you look at the first quarter, all in all, our net sales grew by 2.4%. In constant currency, 3.6%. The growth came from the Top Hammer segment; in the first half, there was an 8.6% increase, whereas in the Down the Hole and Geotechnical segments, we experienced a decline. We highlight this improvement in EBIT. All in all, our EBIT has improved by €3 million. The first half EBIT was €1.7 million compared to -€1.3 million in the first half of 2023. Cash flow from operations has also been improving, and the first half was 22.8 million euros. And, it's coming now mainly from the improved profitability. If you examine the sales by market area during the first half of the year. As mentioned earlier, the growth has been driven by Australasia, which has grown 30% during the first half, driven by new initiatives. Customers, especially in our Top Hammer business. On the other hand, we secured one of the largest supply agreements in Australasia at the end of the second quarter. So that will then actually impact the sales in the second half of the year in Australasia, as bridge sales in Asia and EMEA East have been relatively flat during the first half of the year.
It's a mixed picture within those regions; in EMEA, we have had stronger performance, particularly in Southern Africa and the Nordic countries. And then, we have also been able to achieve quite nice growth. America is down 10%. And this is mainly coming from South America. Uh, and related to some of the contracts that ended in the second half of 2023. Uh, on, uh, steps towards our sustainability goals. I mentioned this great improvement in the CO2 emission intensity reduction. And there we have taken actions to utilize, let's say, green energy. Also, looking at the emission efficiency of the power supply chain, it appears that it has impacted their results. There are also other areas that have progressed well, but naturally many areas still exist where we must put strong emphasis, especially on improving our safety culture and performance. Uh, to read also targets in that area of our sustainability program. We've also launched new innovations to the market. In the second quarter, we launched extreme carbides for our Top Hammer bits. These are graphite, designed for hard and abrasive rock conditions and help our customers achieve an increased lifetime of up to 30%, improved rate of penetration, and also reduced grinding intervals. So kind of clear, tangible, excellent benefits to our customers, for hard applications. We mentioned earlier that we had launched our first model of the Robit® H Series. Series, hammer family. That was the four-inch model. And now we have launched the full range from 4 to 8 inch hammers. Really, it's a modular hammer family. With improved energy efficiency, this is also positively impacting customers' CO2 emissions as well as operating costs. High performance, high rate of penetration. Uh, hammer. But let's take a short look at a video about the archery center. So we say that the Robit® H Series hammer is a modular handle. What does it mean in practice? What you see here are actually four different hammers. We have an A for hammer. We are here with the standard high-power configuration. Let's say the customer would be utilizing the hammer in a softer ground condition, so the compressor power wouldn't be sufficient. What would need to be done is just to change the cylinder, which you can do in a matter of minutes. Then you have a new configuration of the hammer for different ground conditions. Typically, there is a standard version and a tubeless version. There are different configurations of these. Some customers prefer a tubeless version to convert a standard hammer to a tubeless hammer. There are two components you need to change. You need to change the piston and the guide bush again. A simple operation to be done. And then you have again a new configuration that you can have either as a low flow or high power version. So essentially, what we see here are four different panels tasked with changing a couple of different components. So that's what we mean when we say that the design is modular. Uh, but let's go back to the results. Finance was also handed over to Bill.